Product Overview
This is a hand-worn wash mitt in superfine fibre, cut with a separate thumb and finished with an orange bound edge and a ribbed cuff. The pile face is a plush yellow-orange; the back is a flat grey knit. It slips over the hand, so the palm does the work and the fingers stay in contact with the panel. The mitt belongs to the contact stage of a wash. Once the pre-rinse and the foam have taken the heavy dirt off, the pile carries car wash shampoo across the panels and lifts the film that is left behind. Worn rather than held, it keeps pressure even over a curve and lets you feel a high spot before you press on it. That is the difference between this and a sponge or a folded cloth. A sponge keeps grit at the face and drags it along; a folded cloth bunches in the hand and loses contact at the edges and shut lines. The pile here holds the shampoo and keeps the loosened dirt inside it — which is also why it is the first piece most shops replace when they review the car care supplies they put against paint. Wash bays, pre-delivery prep areas and mobile detailers buy it by the carton and treat it as a consumable, replaced when the pile goes flat rather than when the fabric tears. Because the mitt is worn rather than gripped, pressure comes from the palm and fingers and stays even across a curved panel. You feel the shape of the car through it — a raised edge or a stone chip registers before you lean on it, so you ease off instead of finding out afterwards. The separate thumb is what separates a mitt from a bag over the hand. It gives you a working digit for mirror housings, wiper arms, badges and grille slats, and it stops the pile twisting round when you change direction at the edge of a panel. The open cuff slips on over a bare hand or a thin nitrile glove, and the ribbed knit closes around the wrist. Pull it on dry and wet the pile in the bucket afterwards; a cuff soaked before it is on the hand tends to slide. Orange and yellow are there for a practical reason: the mitt is easy to spot in a bucket of suds, and a bay can run one colour on paint and another on the lower panels without stopping to think. It is also the kind of item buyers put into car care kits for a resale programme, or into a starter set for a new bay.
Fibre & Construction
- Superfine fibre pile: fine filaments give a dense, soft face that loads with shampoo and holds loosened dirt inside the pile instead of carrying it back across the panel.
- Deep plush face: the pile holds enough liquid to finish a panel without going dry.
- A dry mitt drags, and dragging is what marks a finish.
- Bound, stitched edge: the edge is bound rather than left as a raw cut, so it does not fray into the pile or open up after repeated soakings.
- Flat grey reverse: a tighter knit back that keeps the mitt's shape when you pull it on wet and stops the whole piece turning into a sponge.
- Ribbed knit cuff: closes around the wrist so the mitt stays on through a full-height reach over the roof instead of ending up on the floor.
- Two-tone finish: the yellow pile against the orange trim makes the working face obvious at a glance, so nobody scrubs a panel with the back of the mitt.
- Light in the hand: the mitt stays comfortable once it is soaked through, so a bay can keep two on the go without wrists tiring.
Wash-Bay Sequence
- Pre-rinse and foam the vehicle first. The mitt belongs to the car wash and shampoo stage, not the stripping stage — flush the loose grit off before the pile touches paint.
- Load the mitt in the bucket and pick up car wash shampoo until the pile is wet through. It should be heavy with suds, not dripping down your forearm.
- Work top down: roof, glass and upper panels first, then doors and wings, with sills and lower panels last so the dirtiest sections never come before the clean ones.
- Rinse the mitt in clean water between sections and reload it. Grit held in the pile is the one thing that turns a contact wash into a polishing job.
- Use the thumb section around mirrors, door handles, badges, grilles and panel gaps, where a flat cloth skips across the surface instead of following it.
- Keep a second mitt for bumpers, wheel arches and wheels so brake dust never travels up to the paint above them.
- Rinse the vehicle down completely before it goes to the drying towel. Shampoo left to dry on a panel leaves a film the next step has to remove.
Care & Replacement
- Rinse the pile under clean water at the end of the shift. Shampoo and grit left to dry in the fibres stiffen the pile and shorten the mitt's working life.
- Wash it by hand or on a gentle machine cycle, then air dry it pile-out. High heat sets the pile and takes the softness out of the face.
- Leave fabric softener and dryer sheets out of the load. They coat the filaments, and a coated pile picks up less water and less shampoo on the next wash.
- Never store it balled up and damp. A mitt left wet in a bucket overnight mats the pile and picks up a smell that follows it back onto paint.
- Keep paint mitts and wheel mitts apart and wash the wheel mitt separately, stored away from the rest of the car care products used on arches and tyres.
- Retire the mitt when the pile flattens or the bound edge starts to lift. A matted face stops lifting dirt and starts pushing it around the panel.
- Hold a small buffer of car care supplies on the shelf so a worn mitt is replaced the same day rather than after the next busy weekend.
Specifications
| Property | Value |
|---|
| Product type | Hand-worn car wash mitt |
| Model | T-708 |
| Material | Superfine fibre |
| Pile face | Plush yellow-orange microfibre |
| Reverse | Flat grey knit with orange trim |
| Cuff | Ribbed knit, open slip-on |
| Unit weight | 0.04 kg per piece |
| Colour | Orange and yellow |
| Application | Contact washing with car wash and shampoo |
| Brand | SURAINBOW |
| Origin | Guangdong, China |
Ordering & Delivery
- Send the brief: the model, colour requirement, order quantity and destination market, plus anything travelling with the mitts — car wash and shampoo, towels or applicators. A complete brief in one message is what makes the quote and the carton plan comparable.
- Sampling and approval: ask your sales contact about sample availability and timing. As car cleaning products manufacturers we would rather you check pile, colour and cuff fit before a carton is produced, and the approved sample is kept as the reference for the bulk run.
- Labels and carton print: if the mitts carry your own logo, header card or carton artwork, send the files with the brief and approve the proof before production — it matters most when the mitts are packed into car care kits where the carton is on display.
- Order quantity: 500 pcs per order, packed 100 pcs to a carton. Ordering in multiples of 100 keeps the carton count and the packing list aligned.
- Payment: TT. The deposit and balance schedule is set out in the order confirmation so both sides are working to the same dates.
- Packing and dispatch: in stock and fast shipping. Each 100-piece carton measures 51 × 52 × 41 cm and weighs 3.5 kg gross, and the dispatch date for your quantity is confirmed when the order is placed. A second size figure of 65.5 × 43 × 65 also appears on the specification sheet, so confirm with your sales contact which measurement your carton marking should carry.
- Balance, shipping and documents: the balance is settled before dispatch, and the commercial invoice, packing list and shipping documents go out with the shipment. Confirm the document set your market needs at order review.
- After-sales and batch traceability: every carton is traceable to the batch it was produced in. If a shipment arrives short, or the pile and colour do not match the sample you approved, send the order reference, batch details, affected quantity and photos so it can be checked against the retained reference.
Scale & Supply Capability
SURAINBOW is run by Guangzhou Liangdian Automotive Supplies Co., Ltd., a factory-trade operation set up in Guangzhou in 2010 and now 50 people strong. Sixteen years in car care have given us a one-stop supply position: our own SURAINBOW lines are held in stock for fast shipping, and an associate factory with modern production equipment and an established quality management system keeps replenishment moving. We take OEM and ODM work and our R&D team develops to your specification. Buyers in the Middle East, the United States, Southeast Asia, Europe, the UK, Russia, Africa and Australia already order from us.
FAQ
Will the mitt mark a coated or sensitive finish?
The pile is superfine fibre, and a clean mitt used with plenty of car wash shampoo is a gentle way to make contact with a panel. The risk comes from grit rather than from the fibre: rinse the mitt between sections, keep a separate one for the lower panels and wheels, and never put a mitt back in the bucket after it has been on a sill.
Is it one size, and will it fit over a glove?
It is a single slip-on size with an open cuff and a ribbed knit wrist, made to be worn on a bare hand. Most technicians wear it straight over a thin nitrile glove without a problem; if your team works in heavier gloves, check the fit with your sales contact before committing to a carton.
Does the mitt work with a foam wash as well as a bucket?
Both. With a bucket, load the pile with shampoo and rinse it between sections. With a foam lance, let the foam loosen the dirt first and bring the mitt in for the contact pass once the heaviest grime has run off. Either way, keep the mitt with the paint-contact car care supplies rather than with the wheel and arch tools.
How is this different from a flat microfibre towel?
A towel is a flat cloth for drying, wipe-down and interior work. The mitt is worn on the hand and belongs to the contact wash, where the pile carries shampoo and the thumb section follows mirrors, handles and grilles. Most buyers keep both in the same car care products order and use them at different stages of the job.
Can the mitt be supplied under our own brand?
Yes — OEM service is accepted, so the mitt can be labelled and packed for your brand. Share the logo, label wording and carton artwork with your sales contact, and confirm the proof before production so the printed carton is ready to go straight into your car care kits.
Do you supply the mitt together with shampoo, towels and applicators?
Yes. As car cleaning products manufacturers we cover the wash stage as a set, and a mixed enquiry can combine the mitt with shampoo, drying towels and applicators. Availability and order details are confirmed item by item, so a distributor can build a full shelf and a shop can restock the whole stage in one shipment.